How to adjust car tyre pressure

Having the right tire pressure is crucial to driving performance. It is as important as having water and oil in the car, but it is often neglected because it is out of sight and out of mind. There are no flashing lights to let you know when your tire pressure is too low or too high, so it is up to you to stay on top of it.
Failure to ensure correct tire pressure can lead to:
Decreased Fuel Efficiency
This can be a killer in today's economy. Adjusting your type pressure is a free way to make your fuel go further, and it only takes ten minutes at your local gas station.

Premature Wear

Unless you've got money to burn you're not going to want to buy new tires more often than you have to.
Accidents
A blowout, or a loss of grip caused by prematurely worn tires can lead to fatal consequences.

How To Check Tire Pressure
Step One
Ascertain what the correct pressure for your tires is. This information can be found on the side of the tyre. Tyre pressure is often expressed in an acceptable range of pressures rather than a single specific number. Filling your tires to the lower end of this number range will give you greater grip by making your tires a little 'softer'.
Step Two
Your tire stems will have rubber caps on them. Remove these before attempting to change your tire pressure.
Step Three
Set the gauge on the air compressor to your desired number.
Step Four
Connect the nozzle to the tire. You will hear a rush of air when it first connects. This should stop when a seal is formed.
Step Five
Let the air compressor do its thing. When your tire is at the correct pressure, remove the nozzle swiftly.
Step Six
Screw those rubber caps back on the stem, repeat three times, and drive safely.

By Roger rager

How to Clean Your ABS Wheel Sensor

Does your ABS light come on consistently and you do not know what is wrong! Well, when you check your code, you may see that it says that your front wheel sensor is damaged. However, that is not always the case.

A lot of times, your ABS wheel sensor is just fine; they just need to be cleaned. Of course, if you take it to a shop, they are going to tell you that you need a new one. So we are going to go over how you can clean your own ABS wheel sensor in your Toyota and save yourself a lot of money. After you clean it, if you are still having the problem, you will need a new one.


However, most people have noted that nine times out of ten, this does indeed fix their problem.
First of all, before you get started, you are going to want to make sure you have everything that you need to perform the job.

The only things that you are really going to need are a ratchet, jack, wheel lock and, of course, a rag or paper towel to clean it off with. After you have all of this stuff, you can feel free to get started. This should only take you an hour or two to do yourself.

Getting Started On Your Wheel Sensor

First, you have to choose which side you want to get started on. You can choose either the passenger side or the driver side; it does not really matter. However, whichever side you do choose, that is the side that you, of course, need to jack up first.

Before you jack up the car, you need to turn the steering wheel to the opposite side that you are working on. For example, if you are working on the driver side, then you are going to want to turn the wheel to the passenger side. Also, when you get it jacked up. You should use a jack stand, not just the jack. You never know how long you will need to have this car jacked up, so you will want the jack stand.


After you turn the wheel and get everything all set up, you will notice that you should be able to locate the ABS wheel sensor very easily. It should be located directly mounted to the knuckle. To take this off, you are going to have to remove the two bolts that are holding them in place. In most Toyota cars, they are 10mm bolts.

However, some of them can change from time to time. Overall, there will be about four bolts you have to take out. To do this, just follow the ABS sensor around so that you can remove all of the bolts. When you get the sensor off, you will notice that it is all covered in dirt. Take your rag or paper towel, and start whipping it off. As you do, you will notice that the very middle of it has a sliver strip that you could not see before.

A lot of times, dirt blocks this and can cause problems, as you found out. After cleaning it, simply reverse the steps you did to reinstall it. Also, be sure to check both of the front ABS sensors. The one on both sides of the car!

Still Having Problems

Most of the time the procedure discussed above will fix any problem that you are having with your ABS sensor. If you have cleaned both of the front sensors and there are still problems, then you do have a damaged ABS sensor.

At this point, you need to get new ones and replace them. If you want, you will be able to install them the same way you cleaned the other ones. However, instead of cleaning the old ones and putting them back on, you can simply put on the new ones.

Overall, this is a one day job that can save you a ton of money. Most people do not notice how much money that they can save by doing this themselves until they actually do it!

5 Benefits of Wheel Alignments - Why to Get Your Wheels Aligned Regularly

Regular wheel alignments are an important part of conscientious car maintenance. Unfortunately, many car owners fail to understand the importance of good wheel alignment, and therefore don't have their alignment checked often enough.

Here are five reasons why getting regular wheel alignments is good for your car, your bank account, and your peace of mind.

1: Better gas mileage. When your wheels are aligned properly, it cuts down on rolling resistance, which means that you car doesn't have to work as hard or burn as much fuel in order to move forward. This is good news for everyone: Not only do you spend less money on gas, but you also get the satisfaction of knowing your car is responsible for less pollution.

2: More mileage out of your tires. Even the slightest problem with your alignment can have disastrous effects on your tires. If your tires have too much or too little toe-in (the degree at which they point in toward each other at the front, like a person who stands pigeon-toed), a narrow strip on each tire will wear down very quickly, causing you to have to get new tires sooner. By getting regular wheel alignments, you ensure that your tires wear evenly, making them last as long as possible.

3: Tire warranties still apply. The problem with your tires wearing from poor wheel alignment is that it usually voids your warranty on the tires. Most warranties only apply to the quality of the goods. In other words, if the tires wear out too soon because of something other than poor quality, then the manufacturer is not responsible. Failing to get wheel alignments often enough is considered to be negligence on the part of the car's owner, and usually means that the warranty is voided.

4: Less wear and tear on other parts. Having the wheels out of alignment can be stressful on the rest of the car, too. It means that you continually need to put pressure on the steering system in order to keep the car straight, and when you brake you often feel the car pull even more sharply, indicating that the brakes are needing to work harder on one side than the other.

5: Easier to drive. One of the biggest advantages of having your wheels aligned properly is that your car is easier to drive. No annoying pull to one side or the other. It's much easier and more pleasant to drive a car that has had regular wheel alignments.

As you can see, there are many reasons why a car owner should be sure to get regular wheel alignments. Not only does having your wheels aligned properly save you money on gas, tires, and other potential repairs, but it also gives you better peace of mind to know that your car is being cared for properly.